A short description of the method used to perform the test
High Performance Liquid Chromatography/ Tandem Mass Spectrometry (LC-MS/MS)
NY State Available
Indicates the status of NY State approval and if the test is orderable for NY State clients.
Lists a shorter or abbreviated version of the Published Name for a test
Lists additional common names for a test, as an aid in searching
Describes the specimen type validated for testing
Defines the optimal specimen required to perform the test and the preferred volume to complete testing
Specimen Type: Serum
Collection Container/Tube: Red top
Specimen Volume: 1 mL
Collection Instructions: Draw blood in a red-top tube(s). (Serum gel tube is not acceptable.) Spin down and send 1 mL of serum refrigerated in a plastic, preservative-free vial.
Specimen Minimum Volume
Defines the amount of sample necessary to provide a clinically relevant result as determined by the Testing Laboratory
Reject Due To
Identifies specimen types and conditions that may cause the specimen to be rejected
| Other || Polymer gel separation tube (SST or PST) |
Specimen Stability Information
Provides a description of the temperatures required to transport a specimen to the performing laboratory, alternate acceptable temperatures are also included
Discusses physiology, pathophysiology, and general clinical aspects, as they relate to a laboratory test
Mean peak CBD plasma concentrations at 3-4 hours post-dose with Sativex at a low dose (5.4 mg of Delta-9 THC and 5.0 mg of Cannabidiol) were 1.6 +/- 0.4 ng/mL and at a high dose (16 mg of Delta-9 THC and 15 mg of Cannabidiol) were 6.7 +/- 2.0 ng/mL.
Following high dose 400 and 800 mg oral synthetic CBD in corn oil administration, mean peak CBD plasma concentrations occurred within 1.5-3 hours post-dose and were 181.2 +/- 39.8 and 221.1 +/- 35.6 ng/mL, respectively.
The ratio of blood to serum or plasma concentration is unknown for this analyte.
Describes reference intervals and additional information for interpretation of test results. May include intervals based on age and sex when appropriate. Intervals are Mayo-derived, unless otherwise designated. If an interpretive report is provided, the reference value field will state this.
Reporting limit determined each analysis
Discusses conditions that may cause diagnostic confusion, including improper specimen collection and handling, inappropriate test selection, and interfering substances
Known Interferences: Excessive amounts of oleamide from plastic tubes
Several factors determine the fee charged to perform a test. Contact your U.S. or International Regional Manager for information about establishing a fee schedule or to learn more about resources to optimize test selection.
- Authorized users can sign in to Test Prices for detailed fee information.
- Clients without access to Test Prices can contact Customer Service 24 hours a day, seven days a week.
- Prospective clients should contact their Regional Manager. For assistance, contact Customer Service.
Provides information regarding the medical device classification for laboratory test kits and reagents. Tests may be classified as cleared or approved by the US Food and Drug Administration (FDA) and used per manufacturer instructions, or as products that do not undergo full FDA review and approval, and are then labeled as an Analyte Specific Reagent (ASR) product.
This test was developed and its performance characteristics determined by NMS Labs. It has not been cleared or approved by the U.S. Food and Drug Administration.
CPT Code Information
Provides guidance in determining the appropriate Current Procedural Terminology (CPT) code(s) information for each test or profile. The listed CPT codes reflect Mayo Clinic Laboratories interpretation of CPT coding requirements. It is the responsibility of each laboratory to determine correct CPT codes to use for billing.
CPT codes are provided by the performing laboratory.
G0480, if appropriate
Provides guidance in determining the Logical Observation Identifiers Names and Codes (LOINC) values for the order and results codes of this test. LOINC values are provided by the performing laboratory.
||Test Order Name
Order LOINC Value
||Test Result Name
Result LOINC Value
Applies only to results expressed in units of measure originally reported by the performing laboratory. These values do not apply to results that are converted to other units of measure.
Test Setup Resources
Test setup information contains test file definition details to support order and result interfacing between Mayo Clinic Laboratories and your Laboratory Information System.
SI Sample Reports
International System (SI) of Unit reports are provided for a limited number of tests. These reports are intended for international account use and are only available through MayoLINK accounts that have been defined to receive them.
SI Normal Reports |
SI Abnormal Reports